Nuclear and Biological Preparedness
 Biological Preparedness face masks
 Battery Chargers
 Firearms Optics, Lasers, and Related
 High Power Wi-Fi devices
 New Items
 APO/FPO & International Orders
 Privacy Policy
 Show Order
 Yahoo! Shopping

Radiolabs Weatherproof Long Range Wireless Access Point / Bridge / Repeater

Extreme Range - Now with 600mW Output!

With the demand for hardy, weatherproof 802.11 b/g wireless hardware on the rise, RadioLabs is proud to offer the RL3022EXT+ Weatherproof High Power Access Point. With 600mw (+27.7dBm) of transmit power built into a sturdy weatherproof enclosure, this unit provides high speed long range wireless coverage where you need it most!

Powered via POE technology (Power-Over-Ethernet) the RL3022EXT+ allows hardware placement flexibility without having to provide power directly to the unit. Just plug the included POE injector unit into your Cable/DSL modem or Network switch or hub, run a standard CAT-5 Ethernet cable to the RL3022EXT+ and your Weatherproof Outdoor Access Point has power and data through a single cable. No extension cords needed!

Get unmatched range with a huge 600mw (+27.7dBm) transmit power and -94 dBm receive sensitivity. This equals up to 15 times the range of an off-the-shelf wireless access point to provide unmatched coverage and connectivity.

The RL3022EXT+ is capable of multiple operation modes. It can be configured as a standard hard-wired wireless access point to provide a long-range wireless signal, it can also be setup in tandem with a secondary RL3022EXT+ as a WDS-enabled bridge to wirelessly link two locations. In addition WDS-enabled bridging, you can also the WDS (wireless distribution system) to repeat the wireless signal for increased range.

No software is required. If using optional antennas or cabling, the Weatherproof High Power Access Point uses an N-Female external antenna connector. This is an exciting new product, and we are happy to offer such a quality item to our customers.

Get unmatched range with 600mW output - Up to 1 mile or more line of sight with an external antenna. Out of the box, you will have all you need to cover an entire office building, home or small neighborhood.

Weatherproof High Power Access Points have too high of output to be used with wireless amplifiers. Under no circumstances should any amplifier be used with these units.

  • Extremely Long Operating Range
  • Easily Connect your Ethernet Devices or high speed connection with Wireless B/G mode
  • Make wireless AP and Bridge mode simultaneously with WDS (repeater)
  • Plug & Play (no driver required, but comes with CD rom manual)
  • Flexible Access Point locations and cost savings (Power-over-Ethernet injector included)
  • Includes mounting hardware and sealed cable assembly for complete weatherproof protection
  • Included 5dB rubberduck antenna
Model # RL3022EXT+
RadioLabs RL3022EXT+ Access Point
Wireless LAN (for Router & Repeater)
Data Rates 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps 108MBPs
Standards IEEE802.11b/g/Super G, IEEE802.1x, IEEE802.3, IEEE802.3u
Compatibility IEEE 802.11g/ IEEE 802.11b
Power Requirements Power Supply: 90 to 240 VDC ± 10% (depends on different
countries) Device: 12 V/ 1A
Status LEDs LAN, WLAN, Power, Link Quality
Regulation Certifications FCC Part 15C/B/E
RF Information
Frequency Band 2.412~2.484 GHz
Media Access Protocol Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Modulation Technology
  • Orthogonal Frequency Division
  • Multiplexing (OFDM)
  • DBPSK @ 1Mbps
  • DQPSK @2Mbps
  • CCK @ 5.5 & 11Mbps
  • BPSK @ 6 and 9 Mbps
  • QPSK @ 12 and 18 Mbps
  • 16-QAM @ 24 and 36 Mbps
  • 64-QAM @ 48 and 54 Mbps
Operating Channels 11 for North America, 14 for Japan, 13 for Europe
Receive Sensitivity (Typical) -97 dBm @ 1 Mbps
-89 dBm @ 11 Mbps
-92 dBm @ 6 Mbps
-74 dBm @ 54 Mbps
Available transmit power (Depend on Different Countries’ Regulation) 28 ± 2dBm @ 1 ~ 11Mbps
27 ± 2dBm @ 6 ~ 24Mbps
25 ± 2dBm @ 36Mbps
23 ± 2dBm @ 48Mbps
22 ± 2dbm @ 54Mbps
RF Connector N-Type Female
Networking Information
Topology Infrastructure
Operation Mode
  • Point-to-Point/ Point-to-Multipoint
  • Bridge
  • WDS-Repeater/AP
  • Client Router
  • AP Router
  • Universal Repeater
Interface One 10/100Mbps RJ-45 LAN Port

• IEEE802.1x / RADIUS Client (EAP-MD5/TLS/TTLS) Support—
AP Mode
• WPA -- Wi-Fi Protected Access
• PSK (Pre share key) with 64/ 128-bit WEP Key
• EAP-MD5/TLS/ TTLS authenticator (AP Mode) support
• MAC address filtering (WLAN)
• Hide SSID in beacons
• Layer 2 Isolation

IP Auto-configuration DHCP client/ server
Configuration Web-based configuration (HTTP)
Firmware Upgrade Upgrade firmware via Web-browser
Dimensions 260(L)mm x 175(W)mm x 65(H)mm
10.24 (L)in x 6.89(W)in x 2.56(H)in
Weight 680 g (1.49 lb.)
Interface IEEE802.3 (10Base-T/100 Base-TX)
Transmission Rate 10/100Mbps (auto sense)
LAN Ports / Connector One (1) 10/100 Base-T RJ-45 ports (Auto MDI/X)
Transmission Encoding Method 10Base-T Manchester coding:
100Base-TX 4B5B/MLT-3
Access Method CSMA/CD
Power Supply 100-120V AC 50/60Hz DC 3.3v, 2.5A Power Over Ethernet
Weight 4 lbs 4 oz.
Operating Environment Operating: -20ºC to 70ºC
Storage: -40ºC to 80ºC - Humidity 5%~95% Typical

Availability: Usually ships the next business day